녹색 에너지를 끝까지 수행하십시오.
디셩 V3 구성 요소
디셩 V3 구성 요소
엘리베이터 견인기의 브레이크 마찰재는 엘리베이터 견인기 어셈블리의 주요 안전 구성 요소 중 하나입니다. 엘리베이터 제동 시스템이 안전하고 효과적으로 작동 할 수 있는지 여부에 직접적인 영향을 미칩니다. 고강도, 상대적으로 낮은 마모, 좋고 안정적인 마찰 성능.
제품 성능
엘리베이터 견인기 브레이크 마찰재 생산은 수지, 고무, 섬유 및 기타 마찰 성능 개질제를 완전히 저어주고 고무 믹서를 통해 완전히 압출 및 융합한 다음 다른 공정으로 만든 예비 성형, 열간 프레스, 가황 및 가공 제품을 거치는 것입니다.
Technical requirements:
1.The pretightening torque of bolts see table 1
2.Add solidified gule (Loctite 243) to part No.5
3.MachiningthearcR345oflining bythe datum of plane A and 4-016.5 on No.1, protect all the holes of No.1 before machining. and clean up all holes after machining.
components
Technical requirementss:
1.Type of Lining: D-007
2.Surface even, no lacunas, no nicks
3.Hardness is HRR70+ 10
4.Frictional coefficient 0.42~0.56(Test method references to the provisions of GB 5763 6.3 friction performance test.
5.Internal shear strength>10MPa.
Technical requirements:
1Material hardness: 160-210 HBW The surface of the cast should be glabrous.
2.The inner stress should be eliminated by temper after casting.
3.Unstated fillets: R3
4.Deburr and chamfer.
5.All the chamfers that aren't labeled are: 0.5x45°
6.The tolerance that isn’t labeled is according to the GB/T1184-1996(K).
7.The non-machined surfaces and surface I Il should be painted. And the surface painting RAL9005, requirements see R000000306.
Technical requirements:
1.The pretightening torque of bolts see table 1
2.Add solidified gule (Loctite 243) to part No.5
3.MachiningthearcR345oflining bythe datum of plane A and 4-016.5 on No.1, protect all the holes of No.1 before machining. and clean up all holes after machining.
components
Technical requirementss:
1.Type of Lining: D-007
2.Surface even, no lacunas, no nicks
3.Hardness is HRR70+ 10
4.Frictional coefficient 0.42~0.56(Test method references to the provisions of GB 5763 6.3 friction performance test.
5.Internal shear strength>10MPa.
Technical requirements:
1Material hardness: 160-210 HBW The surface of the cast should be glabrous.
2.The inner stress should be eliminated by temper after casting.
3.Unstated fillets: R3
4.Deburr and chamfer.
5.All the chamfers that aren't labeled are: 0.5x45°
6.The tolerance that isn’t labeled is according to the GB/T1184-1996(K).
7.The non-machined surfaces and surface I Il should be painted. And the surface painting RAL9005, requirements see R000000306.
